Anunţ

Caută printre mesajele de pe forum înainte de a scrie unul nou!
Formulează corect întrebarea sau problema pe care o ai.
Respectă regulile forumului și Codul de Conduită!

#1 07 Oct 2010 22:44:22

Ovidiu68
Oaspete

Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Sper ca am pus un  titlu cat de decent, daca nu rog pe cineva sa il modereze.
.
Dupa cum bine stim cu totii Unitatile noastre optice ne returneaza de multe ori diferite ERORI si/sau AVERTIZMENTE, insa de cele mai multe ori ele (SCSI) fiind doar sub forma unui cod fara sa furnizeze si informatia respectivei erori ca fiind....ce.
.
.
Eu am sa va impartasesc o lista a mea care o am salvata de cca 3 poate 4 ani insa este posibil sa gasiti liste mai noi care contin unele erori ce nu apar in lista.
Lista de erori si/sau avertizmente este urmatoarea:

Cod:

0 / 00 / 00      NO ADDITIONAL SENSE INFORMATION 
B / 00 / 06      I/O PROCESS TERMINATED
5 / 00 / 11      AUDIO PLAY OPERATION IN PROGRESS
5 / 00 / 12      AUDIO PLAY OPERATION PAUSED
5 / 00 / 13      AUDIO PLAY OPERATION SUCCESSFULLY COMPLETED
5 / 00 / 14      AUDIO PLAY OPERATION STOPPED DUE TO ERROR
5 / 00 / 15      NO CURRENT AUDIO STATUS TO RETURN
4 / 00 / 17      CLEANING REQUESTED
3 / 02 / 00      NO SEEK COMPLETE
2 / 04 / 00      LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE
2 / 04 / 01      LOGICAL UNIT IS IN PROCESS OF BECOMING READY
2 / 04 / 02      LOGICAL UNIT NOT READY, INITIALIZING CMD. REQUIRED
2 / 04 / 03      LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED
2 / 04 / 04      LOGICAL UNIT NOT READY, FORMAT IN PROGRESS
2 / 04 / 07      LOGICAL UNIT NOT READY, OPERATION IN PROGRESS
2 / 04 / 08      LOGICAL UNIT NOT READY, LONG WRITE IN PROGRESS
4 / 05 / 00      LOGICAL UNIT DOES NOT RESPOND TO SELECTION
3 / 06 / 00      NO REFERENCE POSITION FOUND
5 / 07 / 00      MULTIPLE PERIPHERAL DEVICES SELECTED
4 / 08 / 00      LOGICAL UNIT COMMUNICATION FAILURE
4 / 08 / 01      LOGICAL UNIT COMMUNICATION TIME-OUT
4 / 08 / 02      LOGICAL UNIT COMMUNICATION PARITY ERROR
4 / 08 / 03      LOGICAL UNIT COMMUNICATION CRC ERROR (ULTRA-DMA/32)
4 / 09 / 00      TRACK FOLLOWING ERROR
4 / 09 / 01      TRACKING SERVO FAILURE
4 / 09 / 02      FOCUS SERVO FAILURE
4 / 09 / 03      SPINDLE SERVO FAILURE
4 / 09 / 04      HEAD SELECT FAULT
6 / 0A / 00      ERROR LOG OVERFLOW
1 / 0B / 00      WARNING
1 / 0B / 01      WARNING - SPECIFIED TEMPERATURE EXCEEDED
1 / 0B / 02      WARNING - ENCLOSURE DEGRADED
3 / 0C / 00      WRITE ERROR
3 / 0C / 07      WRITE ERROR - RECOVERY NEEDED
3 / 0C / 08      WRITE ERROR - RECOVERY FAILED
3 / 0C / 09      WRITE ERROR - LOSS OF STREAMING
3 / 0C / 0A      WRITE ERROR - PADDING BLOCKS ADDED
3 / 11 / 00      UNRECOVERED READ ERROR
3 / 11 / 01      READ RETRIES EXHAUSTED
3 / 11 / 02      ERROR TOO LONG TO CORRECT
3 / 11 / 05      L-EC UNCORRECTABLE ERROR
3 / 11 / 06      CIRC UNRECOVERED ERROR
3 / 11 / 0F      ERROR READING UPC/EAN NUMBER
3 / 11 / 10      ERROR READING ISRC NUMBER
B / 11 / 11      READ ERROR - LOSS OF STREAMING
3 / 15 / 00      RANDOM POSITIONING ERROR
3 / 15 / 01      MECHANICAL POSITIONING ERROR
3 / 15 / 02      POSITIONING ERROR DETECTED BY READ OF MEDIUM
1 / 17 / 00      RECOVERED DATA WITH NO ERROR CORRECTION APPLIED
1 / 17 / 01      RECOVERED DATA WITH RETRIES
1 / 17 / 02      RECOVERED DATA WITH POSITIVE HEAD OFFSET
1 / 17 / 03      RECOVERED DATA WITH NEGATIVE HEAD OFFSET
1 / 17 / 04      RECOVERED DATA WITH RETRIES AND/OR CIRC APPLIED
1 / 17 / 05      RECOVERED DATA USING PREVIOUS SECTOR ID
1 / 17 / 07      RECOVERED DATA WITHOUT ECC - RECOMMEND REASSIGNMENT
1 / 17 / 08      RECOVERED DATA WITHOUT ECC - RECOMMEND REWRITE
1 / 17 / 09      RECOVERED DATA WITHOUT ECC - DATA REWRITTEN
1 / 18 / 00      RECOVERED DATA WITH ERROR CORRECTION APPLIED
1 / 18 / 01      RECOVERED DATA WITH ERROR CORR. & RETRIES APPLIED
1 / 18 / 02      RECOVERED DATA - DATA AUTO-REALLOCATED
1 / 18 / 03      RECOVERED DATA WITH CIRC
1 / 18 / 04      RECOVERED DATA WITH L-EC
1 / 18 / 05      RECOVERED DATA . RECOMMEND REASSIGNMENT
1 / 18 / 06      RECOVERED DATA . RECOMMEND REWRITE
1 / 18 / 08      RECOVERED DATA  WITH LINKING
5 / 1A / 00      PARAMETER LIST LENGTH ERROR
4 / 1B / 00      SYNCHRONOUS DATA TRANSFER ERROR
A / 1D / 00      MISCOMPARE DURING VERIFY OPERATION
5 / 20 / 00      INVALID COMMAND OPERATION CODE
5 / 21 / 00      LOGICAL BLOCK ADDRESS OUT OF RANGE
5 / 21 / 01      INVALID ELEMENT ADDRESS
5 / 21 / 02      INVALID ADDRESS FOR WRITE
5 / 24 / 00      INVALID FIELD IN CDB
5 / 25 / 00      LOGICAL UNIT NOT SUPPORTED
5 / 26 / 00      INVALID FIELD IN PARAMETER LIST
5 / 26 / 01      PARAMETER NOT SUPPORTED
5 / 26 / 02      PARAMETER VALUE INVALID
5 / 26 / 03      THRESHOLD PARAMETERS NOT SUPPORTED
5 / 26 / 04      INVALID RELEASE OF ACTIVE PERSISTENT RESERVATION
5 / 27 / 00      WRITE PROTECTED
5 / 27 / 01      HARDWARE WRITE PROTECTED
5 / 27 / 02      LOGICAL UNIT SOFTWARE WRITE PROTECTED
5 / 27 / 03      ASSOCIATED WRITE PROTECT
5 / 27 / 04      PERSISTENT WRITE PROTECT
5 / 27 / 05      PERMANENT WRITE PROTECT
7 / 27 / 06      CONDITIONAL WRITE PROTECT
6 / 28 / 00      NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED
6 / 28 / 01      IMPORT OR EXPORT ELEMENT ACCESSED
6 / 29 / 00      POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
6 / 29 / 01      POWER ON OCCURRED
6 / 29 / 02      SCSI BUS RESET OCCURRED
6 / 29 / 03      BUS DEVICE RESET FUNCTION OCCURRED
6 / 29 / 04      DEVICE INTERNAL RESET
6 / 2A / 00      PARAMETERS CHANGED
6 / 2A / 01      MODE PARAMETERS CHANGED
6 / 2A / 02      LOG PARAMETERS CHANGED
6 / 2A / 03      RESERVATIONS PREEMPTED
5 / 2B / 00      COPY CANNOT EXECUTE SINCE INITIATOR CANNOT DISCONNECT
5 / 2C / 00      COMMAND SEQUENCE ERROR
5 / 2C / 03      CURRENT PROGRAM AREA IS NOT EMPTY
5 / 2C / 04      CURRENT PROGRAM AREA IS EMPTY
6 / 2E / 00      INSUFFICIENT TIME FOR OPERATION
6 / 2F / 00      COMMANDS CLEARED BY ANOTHER INITIATOR
2 / 30 / 00      INCOMPATIBLE MEDIUM INSTALLED
2 / 30 / 01      CANNOT READ MEDIUM . UNKNOWN FORMAT
2 / 30 / 02      CANNOT READ MEDIUM . INCOMPATIBLE FORMAT
2 / 30 / 03      CLEANING CARTRIDGE INSTALLED
2 / 30 / 04      CANNOT WRITE MEDIUM . UNKNOWN FORMAT
2 / 30 / 05      CANNOT WRITE MEDIUM . INCOMPATIBLE FORMAT
2 / 30 / 06      CANNOT FORMAT MEDIUM . INCOMPATIBLE MEDIUM
2 / 30 / 07      CLEANING FAILURE
5 / 30 / 08      CANNOT WRITE . APPLICATION CODE MISMATCH
5 / 30 / 09      CURRENT SESSION NOT FIXATED FOR APPEND
5 / 30 / 10      MEDIUM NOT FORMATTED
3 / 31 / 00      MEDIUM FORMAT CORRUPTED
3 / 31 / 01      FORMAT COMMAND FAILED
3 / 31 / 02      ZONED FORMATTING FAILED DUE TO SPARE LINKING
  / 34 / 00      ENCLOSURE FAILURE
  / 35 / 00      ENCLOSURE SERVICES FAILURE
  / 35 / 01      UNSUPPORTED ENCLOSURE FUNCTION
  / 35 / 02      ENCLOSURE SERVICES UNAVAILABLE
  / 35 / 03      ENCLOSURE SERVICES TRANSFER FAILURE
  / 35 / 04      ENCLOSURE SERVICES TRANSFER REFUSED
1 / 37 / 00      ROUNDED PARAMETER
5 / 39 / 00      SAVING PARAMETERS NOT SUPPORTED
2 / 3A / 00      MEDIUM NOT PRESENT
2 / 3A / 01      MEDIUM NOT PRESENT - TRAY CLOSED
2 / 3A / 02      MEDIUM NOT PRESENT - TRAY OPEN
6 / 3B / 0D      MEDIUM DESTINATION ELEMENT FULL
6 / 3B / 0E      MEDIUM SOURCE ELEMENT EMPTY
6 / 3B / 0F      END OF MEDIUM REACHED
6 / 3B / 11      MEDIUM MAGAZINE NOT ACCESSIBLE
6 / 3B / 12      MEDIUM MAGAZINE REMOVED
6 / 3B / 13      MEDIUM MAGAZINE INSERTED
6 / 3B / 14      MEDIUM MAGAZINE LOCKED
6 / 3B / 15      MEDIUM MAGAZINE UNLOCKED
4 / 3B / 16      MECHANICAL POSITIONING OR CHANGER ERROR
5 / 3D / 00      INVALID BITS IN IDENTIFY MESSAGE
2 / 3E / 00      LOGICAL UNIT HAS NOT SELF-CONFIGURED YET
4 / 3E / 01      LOGICAL UNIT FAILURE
4 / 3E / 02      TIMEOUT ON LOGICAL UNIT
6 / 3F / 00      TARGET OPERATING CONDITIONS HAVE CHANGED
6 / 3F / 01      MICROCODE HAS BEEN CHANGED
6 / 3F / 02      CHANGED OPERATING DEFINITION
6 / 3F / 03      INQUIRY DATA HAS CHANGED
4 / 40 / NN      DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH)
5 / 43 / 00      MESSAGE ERROR
4 / 44 / 00      INTERNAL TARGET FAILURE
B / 45 / 00      SELECT OR RESELECT FAILURE
4 / 46 / 00      UNSUCCESSFUL SOFT RESET
4 / 47 / 00      SCSI PARITY ERROR
B / 48 / 00      INITIATOR DETECTED ERROR MESSAGE RECEIVED
B / 49 / 00      INVALID MESSAGE ERROR
4 / 4A / 00      COMMAND PHASE ERROR
4 / 4B / 00      DATA PHASE ERROR
4 / 4C / 00      LOGICAL UNIT FAILED SELF-CONFIGURATION
B / 4D / NN      TAGGED OVERLAPPED COMMANDS (NN = QUEUE TAG)
B / 4E / 00      OVERLAPPED COMMANDS ATTEMPTED
3 / 51 / 00      ERASE FAILURE
3 / 51 / 01      ERASE FAILURE - INCOMPLETE ERASE OPERATION DETECTED
4 / 53 / 00      MEDIA LOAD OR EJECT FAILED
5 / 53 / 02      MEDIUM REMOVAL PREVENTED
5 / 55 / 00      SYSTEM RESOURCE FAILURE
3 / 57 / 00      UNABLE TO RECOVER TABLE-OF-CONTENTS
6 / 5A / 00      OPERATOR REQUEST OR STATE CHANGE INPUT
6 / 5A / 01      OPERATOR MEDIUM REMOVAL REQUEST
6 / 5A / 02      OPERATOR SELECTED WRITE PROTECT
6 / 5A / 03      OPERATOR SELECTED WRITE PERMIT
6 / 5B / 00      LOG EXCEPTION
6 / 5B / 01      THRESHOLD CONDITION MET
6 / 5B / 02      LOG COUNTER AT MAXIMUM
6 / 5B / 03      LOG LIST CODES EXHAUSTED
1 / 5D / 01      FAILURE PREDICTION THRESHOLD EXCEEDED . Predicted Media failure
1 / 5D / 02      LOGICAL UNIT FAILURE PREDICTION THRESHOLD EXCEEDED
1 / 5D / 03      FAILURE PREDICTION THRESHOLD EXCEEDED . Predicted Spare Area Exhaustin
1 / 5D / FF      FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE)
6 / 5E / 00      LOW POWER CONDITION ON
6 / 5E / 01      IDLE CONDITION ACTIVATED BY TIMER
6 / 5E / 02      STANDBY CONDITION ACTIVATED BY TIMER
6 / 5E / 03      IDLE CONDITION ACTIVATED BY COMMAND
6 / 5E / 04      STANDBY CONDITION ACTIVATED BY COMMAND
5 / 63 / 00      END OF USER AREA ENCOUNTERED ON THIS TRACK
5 / 63 / 01      PACKET DOES NOT FIT IN AVAILABLE SPACE
5 / 64 / 00      ILLEGAL MODE FOR THIS TRACK
5 / 64 / 01      INVALID PACKET SIZE
4 / 65 / 00      VOLTAGE FAULT
5 / 6F / 00      COPY PROTECTION KEY EXCHANGE FAILURE . AUTHENTICATION FAILURE
5 / 6F / 01      COPY PROTECTION KEY EXCHANGE FAILURE . KEY NOT PRESENT
5 / 6F / 02      COPY PROTECTION KEY EXCHANGE FAILURE .KEY NOT ESTABLISHED
5 / 6F / 03      READ OF SCRAMBLED SECTOR WITHOUT AUTHENTICATION
5 / 6F / 04      MEDIA REGION CODE IS MISMATCHED TO LOGICAL UNIT REGION
5 / 6F / 05      LOGICAL UNIT REGION MUST BE PERMANENT/REGION RESET COUNT ERROR
3 / 72 / 00      SESSION FIXATION ERROR
3 / 72 / 01      SESSION FIXATION ERROR WRITING LEAD-IN
3 / 72 / 02      SESSION FIXATION ERROR WRITING LEAD-OUT
5 / 72 / 03      SESSION FIXATION ERROR . INCOMPLETE TRACK IN SESSION
5 / 72 / 04      EMPTY OR PARTIALLY WRITTEN RESERVED TRACK
5 / 72 / 05      NO MORE TRACK RESERVATIONS ALLOWED
3 / 73 / 00      CD CONTROL ERROR
1 / 73 / 01      POWER CALIBRATION AREA ALMOST FULL
3 / 73 / 02      POWER CALIBRATION AREA IS FULL
3 / 73 / 03      POWER CALIBRATION AREA ERROR
3 / 73 / 04      PROGRAM MEMORY AREA UPDATE FAILURE
3 / 73 / 05      PROGRAM MEMORY AREA IS FULL
3 / 73 / 06      RMA/PMA IS ALMOST FULL
0 / 00 / 00      NO ADDITIONAL SENSE INFORMATION
B / 00 / 06      I/O PROCESS TERMINATED
2 / 04 / 00      LOGICAL UNIT NOT READY, CAUSE NOT REPORTABLE
2 / 04 / 01      LOGICAL UNIT IS IN PROCESS OF BECOMING READY
2 / 04 / 02      LOGICAL UNIT NOT READY, INITIALIZING CMD. REQUIRED
2 / 04 / 03      LOGICAL UNIT NOT READY, MANUAL INTERVENTION REQUIRED
2 / 04 / 04      LOGICAL UNIT NOT READY, FORMAT IN PROGRESS
2 / 04 / 07      LOGICAL UNIT NOT READY, OPERATION IN PROGRESS
2 / 04 / 08      LOGICAL UNIT NOT READY, LONG WRITE IN PROGRESS
4 / 05 / 00      LOGICAL UNIT DOES NOT RESPOND TO SELECTION
5 / 07 / 00      MULTIPLE PERIPHERAL DEVICES SELECTED
4 / 08 / 00      LOGICAL UNIT COMMUNICATION FAILURE
4 / 08 / 01      LOGICAL UNIT COMMUNICATION TIME-OUT
4 / 08 / 02      LOGICAL UNIT COMMUNICATION PARITY ERROR
6 / 0A / 00      ERROR LOG OVERFLOW
1 / 0B / 00      WARNING
1 / 0B / 01      WARNING - SPECIFIED TEMPERATURE EXCEEDED
1 / 0B / 02      WARNING - ENCLOSURE DEGRADED
5 / 1A / 00      PARAMETER LIST LENGTH ERROR
4 / 1B / 00      SYNCHRONOUS DATA TRANSFER ERROR
5 / 20 / 00      INVALID COMMAND OPERATION CODE
5 / 24 / 00      INVALID FIELD IN CDB
5 / 25 / 00      LOGICAL UNIT NOT SUPPORTED
5 / 26 / 00      INVALID FIELD IN PARAMETER LIST
5 / 26 / 01      PARAMETER NOT SUPPORTED
5 / 26 / 02      PARAMETER VALUE INVALID
6 / 28 / 00      NOT READY TO READY CHANGE, MEDIUM MAY HAVE CHANGED
6 / 29 / 00      POWER ON, RESET, OR BUS DEVICE RESET OCCURRED
6 / 29 / 01      POWER ON OCCURRED
6 / 29 / 02      SCSI BUS RESET OCCURRED
6 / 29 / 03      BUS DEVICE RESET FUNCTION OCCURRED
6 / 29 / 04      DEVICE INTERNAL RESET
6 / 2A / 00      PARAMETERS CHANGED
6 / 2A / 01      MODE PARAMETERS CHANGED
6 / 2A / 02      LOG PARAMETERS CHANGED
6 / 2F / 00      COMMANDS CLEARED BY ANOTHER INITIATOR
  / 34 / 00      ENCLOSURE FAILURE
  / 35 / 00      ENCLOSURE SERVICES FAILURE
  / 35 / 01      UNSUPPORTED ENCLOSURE FUNCTION
  / 35 / 02      ENCLOSURE SERVICES UNAVAILABLE
  / 35 / 03      ENCLOSURE SERVICES TRANSFER FAILURE
  / 35 / 04      ENCLOSURE SERVICES TRANSFER REFUSED
5 / 3D / 00      INVALID BITS IN IDENTIFY MESSAGE
2 / 3E / 00      LOGICAL UNIT HAS NOT SELF-CONFIGURED YET
4 / 3E / 01      LOGICAL UNIT FAILURE
4 / 3E / 02      TIMEOUT ON LOGICAL UNIT
6 / 3F / 00      TARGET OPERATING CONDITIONS HAVE CHANGED
6 / 3F / 01      MICROCODE HAS BEEN CHANGED
6 / 3F / 02      CHANGED OPERATING DEFINITION
6 / 3F / 03      INQUIRY DATA HAS CHANGED
4 / 40 / NN      DIAGNOSTIC FAILURE ON COMPONENT NN (80H-FFH)
5 / 43 / 00      MESSAGE ERROR
4 / 44 / 00      INTERNAL TARGET FAILURE
B / 45 / 00      SELECT OR RESELECT FAILURE
4 / 46 / 00      UNSUCCESSFUL SOFT RESET
4 / 47 / 00      SCSI PARITY ERROR
B / 48 / 00      INITIATOR DETECTED ERROR MESSAGE RECEIVED
B / 49 / 00      INVALID MESSAGE ERROR
4 / 4A / 00      COMMAND PHASE ERROR
4 / 4B / 00      DATA PHASE ERROR
4 / 4C / 00      LOGICAL UNIT FAILED SELF-CONFIGURATION
B / 4D / NN      TAGGED OVERLAPPED COMMANDS (NN = QUEUE TAG)
B / 4E / 00      OVERLAPPED COMMANDS ATTEMPTED
6 / 5A / 00      OPERATOR REQUEST OR STATE CHANGE INPUT
6 / 5A / 01      OPERATOR MEDIUM REMOVAL REQUEST
6 / 5B / 00      LOG EXCEPTION
6 / 5B / 01      THRESHOLD CONDITION MET
6 / 5B / 02      LOG COUNTER AT MAXIMUM
6 / 5B / 03      LOG LIST CODES EXHAUSTED
6 / 5D / 00      FAILURE PREDICTION THRESHOLD EXCEEDED
6 / 5D / FF      FAILURE PREDICTION THRESHOLD EXCEEDED (FALSE)
4 / 65 / 00      VOLTAGE FAULT
4 / 00 / 17      CLEANING REQUESTED
3 / 02 / 00      NO SEEK COMPLETE
3 / 06 / 00      NO REFERENCE POSITION FOUND
4 / 09 / 00      TRACK FOLLOWING ERROR
4 / 09 / 01      TRACKING SERVO FAILURE
4 / 09 / 02      FOCUS SERVO FAILURE
4 / 09 / 03      SPINDLE SERVO FAILURE
4 / 09 / 04      HEAD SELECT FAULT
3 / 11 / 00      UNRECOVERED READ ERROR
3 / 11 / 01      READ RETRIES EXHAUSTED
3 / 11 / 02      ERROR TOO LONG TO CORRECT
3 / 11 / 05      L-EC UNCORRECTABLE ERROR
3 / 11 / 06      CIRC UNRECOVERED ERROR
3 / 11 / 0F      ERROR READING UPC/EAN NUMBER
3 / 11 / 10      ERROR READING ISRC NUMBER
3 / 15 / 00      RANDOM POSITIONING ERROR
3 / 15 / 01      MECHANICAL POSITIONING ERROR
3 / 15 / 02      POSITIONING ERROR DETECTED BY READ OF MEDIUM
1 / 17 / 00      RECOVERED DATA WITH NO ERROR CORRECTION APPLIED
1 / 17 / 01      RECOVERED DATA WITH RETRIES
1 / 17 / 02      RECOVERED DATA WITH POSITIVE HEAD OFFSET
1 / 17 / 03      RECOVERED DATA WITH NEGATIVE HEAD OFFSET
1 / 17 / 04      RECOVERED DATA WITH RETRIES AND/OR CIRC APPLIED
1 / 17 / 05      RECOVERED DATA USING PREVIOUS SECTOR ID
1 / 17 / 07      RECOVERED DATA WITHOUT ECC - RECOMMEND REASSIGNMENT
1 / 17 / 08      RECOVERED DATA WITHOUT ECC - RECOMMEND REWRITE
1 / 17 / 09      RECOVERED DATA WITHOUT ECC - DATA REWRITTEN
1 / 18 / 00      RECOVERED DATA WITH ERROR CORRECTION APPLIED
1 / 18 / 01      RECOVERED DATA WITH ERROR CORR. & RETRIES APPLIED
1 / 18 / 02      RECOVERED DATA - DATA AUTO-REALLOCATED
1 / 18 / 03      RECOVERED DATA WITH CIRC
1 / 18 / 04      RECOVERED DATA WITH L-EC
1 / 18 / 05      RECOVERED DATA . RECOMMEND REASSIGNMENT
1 / 18 / 06      RECOVERED DATA . RECOMMEND REWRITE
5 / 21 / 00      LOGICAL BLOCK ADDRESS OUT OF RANGE
2 / 30 / 00      INCOMPATIBLE MEDIUM INSTALLED
2 / 30 / 01      CANNOT READ MEDIUM . UNKNOWN FORMAT
2 / 30 / 02      CANNOT READ MEDIUM . INCOMPATIBLE FORMAT
2 / 30 / 03      CLEANING CARTRIDGE INSTALLED
2 / 30 / 07      CLEANING FAILURE
3 / 31 / 00      MEDIUM FORMAT CORRUPTED
2 / 3A / 00      MEDIUM NOT PRESENT
2 / 3A / 01      MEDIUM NOT PRESENT - TRAY CLOSED
2 / 3A / 02      MEDIUM NOT PRESENT - TRAY OPEN
3 / 57 / 00      UNABLE TO RECOVER TABLE-OF-CONTENTS
6 / 5E / 00      LOW POWER CONDITION ON
6 / 5E / 01      IDLE CONDITION ACTIVATED BY TIMER
6 / 5E / 02      STANDBY CONDITION ACTIVATED BY TIMER
6 / 5E / 03      IDLE CONDITION ACTIVATED BY COMMAND
6 / 5E / 04      STANDBY CONDITION ACTIVATED BY COMMAND
5 / 63 / 00      END OF USER AREA ENCOUNTERED ON THIS TRACK
5 / 64 / 00      ILLEGAL MODE FOR THIS TRACK
3 / 73 / 00      CD CONTROL ERROR
3 / 0C / 00      WRITE ERROR
3 / 0C / 07      WRITE ERROR - RECOVERY NEEDED
3 / 0C / 08      WRITE ERROR - RECOVERY FAILED
3 / 0C / 09      WRITE ERROR - LOSS OF STREAMING
3 / 0C / 0A      WRITE ERROR - PADDING BLOCKS ADDED
5 / 27 / 00      WRITE PROTECTED
5 / 27 / 01      HARDWARE WRITE PROTECTED
5 / 27 / 02      LOGICAL UNIT SOFTWARE WRITE PROTECTED
5 / 27 / 03      ASSOCIATED WRITE PROTECT
5 / 27 / 04      PERSISTENT WRITE PROTECT
5 / 27 / 05      PERMANENT WRITE PROTECT
2 / 30 / 04      CANNOT WRITE MEDIUM . UNKNOWN FORMAT
2 / 30 / 05      CANNOT WRITE MEDIUM . INCOMPATIBLE FORMAT
5 / 30 / 08      CANNOT WRITE . APPLICATION CODE MISMATCH
5 / 30 / 09      CURRENT SESSION NOT FIXATED FOR APPEND
5 / 30 / 10      MEDIUM NOT FORMATTED
6 / 5A / 02      OPERATOR SELECTED WRITE PROTECT
6 / 5A / 03      OPERATOR SELECTED WRITE PERMIT
1 / 73 / 01      POWER CALIBRATION AREA ALMOST FULL
3 / 73 / 02      POWER CALIBRATION AREA IS FULL
3 / 73 / 03      POWER CALIBRATION AREA ERROR
3 / 73 / 04      PROGRAM MEMORY AREA UPDATE FAILURE
3 / 73 / 05      PROGRAM MEMORY AREA IS FULL
5 / 2C / 03      CURRENT PROGRAM AREA IS NOT EMPTY
5 / 2C / 04      CURRENT PROGRAM AREA IS EMPTY
3 / 72 / 00      SESSION FIXATION ERROR
3 / 72 / 01      SESSION FIXATION ERROR WRITING LEAD-IN
3 / 72 / 02      SESSION FIXATION ERROR WRITING LEAD-OUT
5 / 72 / 03      SESSION FIXATION ERROR . INCOMPLETE TRACK IN SESSION
5 / 72 / 04      EMPTY OR PARTIALLY WRITTEN RESERVED TRACK
.
.
.

Acest topic face referire la una dintre clasicele Erori ale Coleg-ului nostru de AICI
Toate Bune .

 

#2 05 Nov 2011 19:57:40

ionreparatorul
Banned
Locaţie: Chisinau
Înregistrat: 09 Jun 2011
Mesaje: 182
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

EU REPAR LAPTOP-URI ... SMD BGA

Asa ca pot spune din experietna ca un cd-rom ... optic ...
fi apsolut OK dar  sa vi-se para ca este defect , sa nu puteti instala windows-ul ... cu el ca si cand nu ar citi bine !
Si acesta manifestare poate aparea nu datorita opticului folosit ci datorita proastei functionari a uneia dintre memoriile RAM !!!
Ram care in teste functioneaza perfet !
Dar in practica dupa ce o sa il inlocuitit sa vedeti cat de bine o sa merga opticul respectiv smile
Daca aveti in realitate probleme cu un optic in general are un semireglabil de unde puteti regla focusul pe lentila , alimentarea laserului ,  eventual in prima faza incercati stergerea lentilei cu un betisor de ureche si alcool izopropilic ! 99,6% alcool ! ( alt alcool lasa urme si dizolva cauciucul plasticul eventual lentila care poate fi din plastic nu din sticla asa cum ne asteptam , niciodata nu incercati spirt pe nici un fel de lentile  ... foto ... pt ca daca aveti ne noocul sa fie din plastic acestea se vor albi matiza si eventual increti !)


omul cat traieste invata (unii traiesc degeaba)

Offline

 

#3 06 Nov 2011 08:33:58

geosoft1
Membru
Locaţie: Râmnicu Vâlcea
Înregistrat: 21 Sep 2009
Mesaje: 3735

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

foarte interesanta teoria prin care daca scoti o memorie buna, merge cdrom-ul.... yikes

din pacate cred ca lucrurile stau totusi altfel... desi memoria RAM poate fi mapata oricum, controlerul DMA nu poate lucra cu orice  zona de memorie fizica. de obicei foloseste o zona de memorie, din primul slot dar pe la inceput. asta inseamna ca daca scoti memoria din primul slot fortezi sistemul sa foloseasca cdrom-ul fara canal DMA in mod pool, ceea ce inseamna alta mod de lucru cu controlerului de disc si un timp de asteptare dupa date mai mare.

astfel, un cdrom obosit poate va mai merge o vreme dar asta nu inseamna ca acel cdrom nu trebuie inlocuit pentru ca nu exista calculator la care merge cdromul numai daca ii scoti o memorie...

pe de alta parte lentilele se calibreaza in fabrica de un robot pe baza unor masuratori, daca umbli la focalizare cu surubelnita eu zic ca nu o mai reglezi bine nici cu slujbe...

se vor albi matiza si eventual increti

de lentile incretite nu am mai auzit yikes... poate ne explici si noua fenomenul....

Editat ultima oară de geosoft1 (06 Nov 2011 08:44:25)


Daca raspunsul nu te multumeste, probabil nu ai pus intrebarea potrivita.
Registered linux user #542751

Offline

 

#4 06 Nov 2011 11:55:01

big_bum
Membru
Locaţie: $HOME
Înregistrat: 30 Nov 2010
Mesaje: 2432
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Partea cu memoriile e adevarata, sorry geosoft. Nu imi pot explica de ce, dar a mers de fiecare data.


Linuxul e ca femeile. Odata ce te-ai prins cum sa lucrezi cu el, vrei sa incerci mai multe distributii.
Inregistreaza-te pe Dropbox si primim amandoi 500MB in plus.
Nexus 5 kernel
Bumberry Pi - a blog running on a Raspberry Pi about Raspberry Pi running a blog.

Offline

 

#5 03 Dec 2011 13:02:12

ibancioiu
Membru
Locaţie: Sibiu
Înregistrat: 17 Jul 2011
Mesaje: 164
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Asa este... cunosc o persoana care nu putea sa instaleze nimic... nici macar os-ul windows/linux... i-am schimbat ramii si a mers din prima fara erori... deci e clar ca nu opereaza corect pe memoria ram... poate un banc de momorie e ars... sau alte chestii legate de ram... eu zic sa imprumuti daca ai de la cn o/doua placute in functie de cate ai .... sa fie acelasi model (non-ddr/ddr2/ddr3) depinde de slot, iar dc merge sa iti cumperi placutele.....

astept sa-mi spui cum ai rezolvat problema...


Dell Vostro 1015
@@@ 4 Gb RAM - DDR 3@@@
@@@ Intel DuoCore 2.20 GHz@@@
@@@ Ubuntu 12.04 LTS @@ i386 @@@

Offline

 

#6 12 Dec 2011 12:43:14

vanila75
Membru
Înregistrat: 19 Mar 2011
Mesaje: 37

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

de ceva vreme am si eu probleme cu dvd-rw, in sensul ca da erori la citirea discurilor, erori la scriere. sistemul este luat in februarie anul acesta, iar unitatea optica in martie.  un ajutor (explicatie) aceste probleme. de retinut ca aceste probleme sunt in urma unor update-uri facute la sistem. am instalat U 11.04 i386. va multumesc pentru un eventual raspuns.

Offline

 

#7 24 Jan 2012 14:51:04

ionreparatorul
Banned
Locaţie: Chisinau
Înregistrat: 09 Jun 2011
Mesaje: 182
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Puteti scapa de unele erori facand UPGRADE de firmware exemplu :   
http://www.cdrinfo.com/Sections/Articles/Sources/LG_GSA-4163B/Images/firmware_flash.png
aici puteti gasi firmware pentru foarte multe optice de la cd-rom-uri foarte vechi pana la dvd-rw din zilele noastre
http://www.cdrinfo.com/Sections/Firmware/Home.aspx

Editat ultima oară de ionreparatorul (24 Jan 2012 14:52:04)


omul cat traieste invata (unii traiesc degeaba)

Offline

 

#8 24 Jan 2012 15:13:58

marianvasile
Administrator
Locaţie: Bucuresti
Înregistrat: 15 Jan 2008
Mesaje: 4042

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

^ Da, ca soluție pentru sisteme windows...


Tot ceea ce mâinile tale prind să săvârșească, fă cu hotărâre, pentru că în groapa în care te vei duce nu există nici faptă, nici punere la cale, nici știință și nici înțelepciune. (Ec. 9:10)

Offline

 

#9 24 Jan 2012 16:04:15

geosoft1
Membru
Locaţie: Râmnicu Vâlcea
Înregistrat: 21 Sep 2009
Mesaje: 3735

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

@ionreparatorul, ar fi apreciate solutiile linux la diversele probleme. solutii windows suntem convinsi ca exista...


Daca raspunsul nu te multumeste, probabil nu ai pus intrebarea potrivita.
Registered linux user #542751

Offline

 

#10 24 Jan 2012 18:27:16

vladi
Membru
Locaţie: București
Înregistrat: 27 May 2011
Mesaje: 1077

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

@ionreparatorul

La modelul tau de dvd wrter (LG 4163), ultimul firmware este A106. L-am actualizat si eu acum 5 ani tongue

Editat ultima oară de vladi (24 Jan 2012 18:27:31)

Offline

 

#11 01 Sep 2012 17:52:15

ionreparatorul
Banned
Locaţie: Chisinau
Înregistrat: 09 Jun 2011
Mesaje: 182
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Solutia prezentata de mine mai sus nu era o solutie neaparat pentru windows !
ci era o solutie care aducea o modifcare hardware a firmwarer-ului acelui DVD-RW ( optic )
Firmwarer-ul acelui optic ramanad in continuare scris cu ultima verisune
indiferent de ce sistem de operare ati fi pus pe acea masina .

Daca vreti sa fie chiar pentru linux ... ubuntu ... puneti mana si faceti ca WINE sa aiba legatura directa cu realitatea ! sa nu mai fie atat de virtual , pe mine ma streseaza ca nu pot sa folosesc programe exe care au directa actiune asupra hardwarer-ului sa le rulez direct sub Ubuntu cu ajutorul wine !
Ar fi foarte interesat daca ati face WINE sa aiba actiune directa asupra realitatii la fel ca si cand ar fi windowz!
Chiar mi-ar fi de mare folos la scrirerea firmwarer-urilor hdd-urilor sau la programarea de PIC-uri FPGA-uri Eeprom-uri epromuri si alte lucruri automatizari chestii interesante ce in mod normal la windowz merge dar la WINE nu .


omul cat traieste invata (unii traiesc degeaba)

Offline

 

#12 01 Sep 2012 18:01:25

ionreparatorul
Banned
Locaţie: Chisinau
Înregistrat: 09 Jun 2011
Mesaje: 182
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

@vladi : http://lgodd.lge.com/fwdrv/DVD-WRITER/GSA4163A106.exe http://www.cdrinfo.com/forum/upfiles/24 … 3A7F46.jpg
http://i44.photobucket.com/albums/f47/g … B-A105.png

http://www.firmwarehq.com/download_442- … 6.exe.html
http://lgodd.lge.com/fwdrv/DVD-WRITER/GSA4163A106.exe
Hai sa iti spun rezolvarea pentru Ubuntu ca sa nu mai fiu tras de urechi ca dau rezolvari pentru window$
uite dezarhivezi executabilul ce contine firmwarer-ul , vei gasi acolo un utilitar si un firmware
apoi iei acel fisier firmwarer-ul
cumperi un programator de bios-uri dai pe el 500 ron minim si mai dai pe adaptor 900 ron care face doar adaptarea de mufa pentru a putea pune memoria flash care se afla pe partea electronica a opricului tau in programatorul de bios-uri ( adica pe o mufa dai o gramada de bani  , eu am dat si acum m-am saturat de jucarie pentru ca trebuie sa citesti imens de mult ca sa poti programa vre-o memorie pt ca programtorul are doar cateva memorii in lista si niciodata pe aia pe care o cauti tu dar trebuie sa gasesti echivalenti , o intrega alergatura , cred ca iti ia si 3 zile de citit 20 de ore / zi , in sfasit gasesti cu ce este echivalent din lista programatorului tau , apoi iei continutul acelei melorii
adica firmwarer-ul gasit in executabilul dezarhivat si il scrii cu programatorul direct din ubuntu pe memorie )
a daca programatorul are soft-uri dezvoltate pentru ubuntu , si aici o mare alergatura sa afli cum sar face sa poti folosi programatorul . Trebuie sa iti mai cumperi si o lupa mare cu neon + un letcon termostatat + o statie de lipit cu aer cald + 1 penseta + flux + fludor.
Dar in final dupa ce aloci multi bani si ani vei castiga experienta.

Acum mi-am adus aminte vezi ca unitatile OPTICE au direct fire trase de la firmware poti sa te conectezi la unele dintre ele fara sa le mai dai jos integratul cu aer cald.
http://static.trustedreviews.com/94%7c2 … -asus2.jpg
vezi locul acela galben de pe cablaj langa mufa de audio out digital
unde ar fi trebuit sa fie pusi niste pini dar ei lipsesc ,
acolo vei pune tu niste pini
si vei cauta cum te poti conecta la pinii respectivi din terminal de la ubuntu trebuie sa ii trimiti datele in cod asci
firmwarer-ul respectiv trebuie sa i-l trimiti printr-o mufa de seriala , cred ca trebuie eventual sa mai faci si un montaj simplu electronic, sau eventual sa cumperi un mic programator de memrorii bios-uri ... care sa cunoasca integratul respectiv
sau cauti o schema cu un cablu de tel nokia caruia ii tai mufa si il lipesti direct pe acei pini http://assets.overclock.net.s3.amazonaw … 96234.jpeg

Editat ultima oară de ionreparatorul (01 Sep 2012 18:23:34)


omul cat traieste invata (unii traiesc degeaba)

Offline

 

#13 09 Sep 2012 21:52:05

danjoe
Membru
Înregistrat: 03 Feb 2010
Mesaje: 105

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Intel Celeron 2.4, ram 1Gb, HDD 80 GB, 40WinXp si 40Unbuntu 12.04 LTS
Unitate optica - DVD sau CD, writer sau rom, am schimbat mai multe, este vizibila in BIOS, vizibila cu XP dar in UBUNTU=NIMIC, Nada, NOTHING!
Va rog un pic de ajutor pentru rezolvare.
Nu ma dau mare, folosesc net, editare text, vreau sa-l folosesc si media, filem/muzici/ dar nu pot folosi unitate optica.
De instalat am venit in timp de la 7.04 cu Ubuntu pe bucatica lui de HDD, cum a vrut, ori update ori reinstalat, de regula de pe net.
Cu multumiri

13.09.2012 Chiar nimeni nu-mi zice nimic?

Editat ultima oară de danjoe (13 Sep 2012 17:35:47)

Offline

 

#14 14 Apr 2013 18:08:40

rocket1982
Banned
Locaţie: Tulcea
Înregistrat: 10 Mar 2012
Mesaje: 85

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

pai sa reluam .... ce unitate optica ai..te rog foloseste aida64  pe windows si spunene modelul...
apoi sa realizam un firmware upgrade tot pe windows daca este posibil...
pasul 3 ar fi sa ne spui ce setari ai in bios pt unitate (daca este ide te rog sa te uiti daca ai jumperi configurati pe cd rom /master/slave /cable select)

sa incepem cu inceputul... rog fara critici la adresa folosirii win ului....

Editat ultima oară de rocket1982 (14 Apr 2013 18:09:38)

Offline

 

#15 14 Apr 2013 19:57:30

Ăla mic
Moderator
Locaţie: Constanța
Înregistrat: 10 Feb 2010
Mesaje: 5592

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

..... sa incepem cu inceputul .....

Începutul ar fi putut fi constituit dintrun mesaj privat către @danjoe cu un conținut de genul :
"Salut, mai ești interesat de rezolvarea problemei enunțate pe forum acum 7 luni ? "

Daca răspunsul ar fi fost de genul :
"Da, poti să mă ajuți ?"

atunci ai fi avut mai multe șanse să nu fi scris mesajul de mai sus degeaba. Cred.
.

Editat ultima oară de Ăla micu' (14 Apr 2013 19:58:10)


[REZOLVAT] ? => DONEAZĂ !   GRUB2   E1-571    Ce este un forum?   Anti-troll   Ubuntu = umanitate către ceilalți

Offline

 

#16 14 Apr 2013 21:47:13

butelie
Membru
Locaţie: Slatina
Înregistrat: 01 Jul 2007
Mesaje: 220
Site web

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

Ăla micu' a scris:

............................................atunci ai fi avut mai multe șanse să nu fi scris mesajul de mai sus degeaba. Cred..

Lasa ca e bine ca se scrie despre asta, ca sa ne lamurim si noi cum e treaba, ca vad ca e destul de imbarligata rezolvarea problemei.


Forum Romania Inedit
O zi buna in continuare !

Offline

 

#17 15 Apr 2013 14:45:54

rocket1982
Banned
Locaţie: Tulcea
Înregistrat: 10 Mar 2012
Mesaje: 85

Re: Erori intalnite pe timpul utilizarii unei medii optice (dvd/cd-rom)

... Am postat tocmai pt ca omul nu a avut suport pt 7 luni  si pt ca aici ar trebuii sa existe o "comunitate"

al doile motiv ar fi faptul ca postul asta este facut permanent /FIXAT ..... deci inca se cauta solutii!!!

Multumesc pt intelegere.

Offline

 
Feed

Antet forum

Powered by FluxBB